discussed in this manual. The official Honda Service Manual for your CRF is available (page ). It is the same manual your dealer uses. If you plan to do any. Honda CRF R Pdf User Manuals. View online or download Honda CRF R Assembly Instructions Manual. View and Download Honda CRFR owner’s manual online. Honda CRFR. CRFR Motorcycle pdf manual download.
|Published (Last):||2 April 2008|
|PDF File Size:||14.53 Mb|
|ePub File Size:||2.16 Mb|
|Price:||Free* [*Free Regsitration Required]|
Remove the clutch pressure plate 8. Clean the piston ring thoroughly.
CRFR Honda Motorcycle Service Manual – Cyclepedia
Remove the exhaust joint pipe page Chapters Table Of Contents Use genuine Honda parts or their equivalent when servicing your CRF. Do not damage the piston rings and cylinder walls.
Install a new gaskets 5 to the exhaust joint 9 muffler clamp bolt pipe 6. Page 75 Do not let the washers and nuts fall into the 7 engine hanger plates crankcase. Oxygenated Fuels Some conventional gasolines are being blended If you notice any undesirable operating with alcohol or an ether compound. Inspect and Clean, Adjust, Lubricate or Replace if necessary. Temporarily install the fork damper to the outer tube.
Page 73 Do not align the piston pin clip end gap with the piston cut-out 6. Measure the float level 25 with the float 11 and accelerator pump cover Disconnect the fuel line 8 from the fuel nut. Your Honda Dealer Once you purchase your new Honda, get familiar Your dealer can inform you about competition with the organization of your Honda dealer so events in your area. Remove the seat mounting bolts 1. Riding your motorcycle is more fun than spending a bucket load of money fixing something you could have prevented with a little time and the right information.
After installing the fork leg page tighten the fork damper to the specified torque: Do not operate the brake lever after the front wheel is removed.
The Importance Of Maintenance Improperly crf2550r this motorcycle or failing to correct a problem before you ride can cause a crash in which you can be seriously hurt or killed. You can be burned or getting dirt, dust or water in the fuel tank.
Installation can be done in the reverse order of removal. Recorded valve clearance C: Rotate the crankshaft by turning the primary 2. Reinstall the crankcase breather tube plug.
2008 Honda CRF250R — Owner’s Manual – Page #15
Remove the dowel pins 3 and cylinder 1 piston ring gasket 4. Set the axle holder 22 in a vise with a piece of The outer tube can drop on the slider and and turn the adjuster counterclockwise nanual it damage the fork dust seal 19 and guide bushing Injury from moving parts. Loosen the nuts in a crisscross pattern in two or three steps.
Replace every 2 years. Set the fork damper 1 in a vise with a piece Loosen the insulator band screw 2. Replacement requires mechanical skill. Enter text from picture: Refer to Safety Precautions on page With your CRF on a box or workstand front 3.
Got it, continue to print. Screw in the lock nut 7 to the fork damper Idle Speed Adjustment The best way to assure proper carburetion is to see your Honda dealer for regularly scheduled 1.
Maintenance Schedule If you do not feel capable of performing a given task or need assistance, remember that your Honda dealer knows your CRF best and is fully equipped to maintain and repair it. Tighten the camshaft holder bolts in a criss-cross 18 feeler gauge pattern in two or three steps.
Connect the fuel line 3 to the fuel valve. If the level is at or below the LOWER level mark, With the motorcycle in an upright position, check check the brake pads for wear page Service the air cleaner more frequently if you ride in unusually wet or dusty areas. To meet clean air standards, some areas of the United States use oxygenated Fuel system damage or performance problems fuels to help reduce emissions.